Would you like to make this site your homepage? It's fast and easy...
Yes, Please make this my home page!
Swan 350
Description:
The Swan 350, no doubt one of Swan's most popular series of transceivers, evolved over the years to the 350C, then into the 350B and 350D, the last of the line.
With a suitable power supply, operation may be fixed, portable, or mobile. Power input on all bands exeeds 400 watts PEP on single sideband, and 230 watts dc input on CW. The basic 5 band transceiver includes AGC, ALC, and grid block CW keying.
Specifications:
(Model 350) - FREQUENCY RANGES:
80 meters 3.5 to 4.0 mc LSB
40 meters 7.0 to 7.5 mc LSB
20 meters 13.85 to 14.350 mc USB
15 meters 21.0 to 21.5 mc USB
10 meters 28.5 to 29.0 mc USB
POWER INPUT:
Single Sideband, Suppressed Carrier is 400 watts PEP minimum on all bands.
CW, 320 watts, dc input on all bands.
AM, Single Sideband with Carrier, 125 watts dc input on all bands.
DISTORTION:
Distortion products down at least 30 db.
UNWANTED SIDEBAND SUPPRESSION:
Unwanted sideband down at least 40 db.
CARRIER SUPPRESION:
Carrier suppression at least 50 db.
RECEIVER SENSITIVITY:
Less than 0.5 microvolt at 50 ohms impedance for signal-plus-noise ratio of 10 db.
AUDIO OUTPUT AND RESPONSE:
Audio output is approx. 3 watts to a 3.2 ohm load. Response essentially flat 300 to 3000 cps in both receive and transmit.
TRANSMITTER OUTPUT:
Wide range Pi-network output matches antennas essencially resistive at 20 to 300 ohms impedance, with coarse and fine load adjustment.
METERING:
Power amplifier cathode current 0-800 ma on transmit, S-meter 0-70 db over S9 on receive.
FRONT PANEL CONTROLS:
Rec-Tune-CW, AF Gain, RF Gain, Mic. Gain, Bandswitch, Carrier Balance, PA Plate Tune, PA Grid Tune, PA Load Coarse, PA Load Fine, VOX-PTT Switch.
REAR PANEL CONTROLS:
Bias potentiometer, Grid-Block CW Key Jack, Jones plug power connector, Vox connector, Antenna (SO239), S-Meter Zero, SPDT relay terminal strip.
VACUUM TUBE COMPLEMENT:
- V1 6EW6 VFO Amplifier
- V2 12BE6 Transmitter Mixer
- V3 6GK6 Driver
- V4 6HF5 PA
- V5 6HF5 PA
- V6 12BZ6 Receiver RF Amp
- V7 12BE6 Receiver Mixer
- V8 6EW6 First IF Amplifier
- V9 12BA6 Second IF Amplifier
- V10 12AX7 Product Detector / Receiver Audio
- V11 6BN8 AGC Amplifier / Detector
- V12 6GK6 Audio Amplifier
- V13 7360 Balanced Modulator
- V14 12BA6 Carrier Oscillator
- V15 12AX7 Mic. Amplifier / Transmit Audio
- V16 0A2 Voltage Regulator
POWER REQUIRMENTS:
Filaments; 12.6 volts, 5.5 amps, ac or dc.
Relay; 12 volts dc, 250 ma.
Bias; -110 volts dc, 100 ma.
Medium Voltage; 275 volts dc, 150 ma.
High Voltage; 800 volts dc, 500 ma.
The most common power supply that was used with the Swan 350, and many other models, was the combination speaker / power supply which matched the unit. For home use, the 120 VAC units were the "117C", "117XC", and the model "412" DC supply for mobile use was available.
DIMENSIONS AND WEIGHT:
Height 5.5 inches
Width 13 inches
Depth 11 inches
Weight 17.25 lbs.
Images:
 | Color Picture | |
